#F link jablotron version 4.0 pdf#
#F link jablotron version 4.0 update#
#F link jablotron version 4.0 manual#
#F link jablotron version 4.0 software#

Notes: When the device is switched on, the system indicator (2) will start flashing yellow repeatedly to indicate that the keypad has not yet been enrolled to the system. Proceed according to the control panel Installation manual. Make sure the conductors do not touch the tamper contact spring. Insert the keypad back into the plastic base and lock the bottom tab using the little screw. Always switch the power off before connecting the keypad to the BUS. For easier installation you can detach the BUS terminals, connect the cables and re-attach them.

Connect the cable to the BUS terminals (7). To meet the criteria of EN 50131 grade 2 the plastic base must be screwed by at least two screws using the mounting hole next to the tamper contact hole and the mounting hole in the diagonal corner. We recommend using all four mounting holes and screws to attach the plastic base. Break away a hole in the plastic base, run the cable through and screw the plastic back on a selected place.

Figure 1 : 1 - status indicators 2 - system indicator 3 - LCD display 4 - keypad and the RFID reader 5 - function buttons A, B, C, D 6 - keypad opening tab 7- detachable BUS terminals 8 - tamper contact 9 - production number Installation Open the keypad housing by pressing the tab on the bottom (6) using a screwdriver. A B c JABLOTRON C4C5JC€IÄI JABLOTRON 1 2 3 7 4 8 5 9 6 r71Ä S GND S ND 1. The keypad contains 4 function buttons (5), an LCD display (3), a system indicator (2), status indicators A, B, C, D (1 a keypad with an RFID chip card/tag reader (4).

#F link jablotron version 4.0 manual#

It is necessary to use this manual in combination with the JABLOTRONIOO installation and user manuals. Using an extema/ input a door detector can be connected to the keypad. ****** ****** JA-IIO BUS keypad The keypad is a component of the JABLOTRONIOO system used to control the control pane/ and display its current status.

#F link jablotron version 4.0 pdf#

Latest A-Link package version 1.1.1.654 to download (AZOR firmware LO60312)Click here to download JABLOTRON JA-110 (01) PDF MANUAL

#F link jablotron version 4.0 software#

The firmware in the communicator and the A-Link software are now up-to-date and ready to be used again. 2 minutes till the red LED (labeled GSM) goes off. The A-Link program stops and performs a communicator restart. Select the file with a *.fwx extension from the folder, where you saved it (in step 10).

#F link jablotron version 4.0 update#

As a confirmation, two LEDs flash with a blue color.ĭownload fwx update and also save the latest fwx software to your hard drive (it is a second file).Ī) Run the A-Link program again and it performs the second step of the update itself using the file with a *.fwx extension from the folder, where you saved it (step 10).ī) If the firmware version in your Azor is LO60309 or higher, in the main menu select the 'Communicator' tab - choose 'Update software'. Select the file with a *.fwp extension from the folder, where you saved it (step 5).įollow the instructions on the screen and wait till the update is finished. In the main menu select the 'Communicator' tab - choose 'Update software'. If your firmware is LO60309 or higher, go to step no.10.ĭownload fwp update and save the latest fwp software to your hard drive. Please check the version of firmware in your Azor (click the 'Version' tab and check the 'Firmware' field).

Run the A-Link program on the newly assigned communicator logical drive. Make sure that the communicator is powered by a power supply before starting the upgradeĬonnect the communicator to your PC via a USB cable. Note: This version includes innovative certificate for antivirus software. Latest A-Link package version 1.1.1.654 to download (AZOR firmware LO60313)